EKC 202D1 PDF

Mobei I copy the parameters from other controller to this one, but noting has change. The function is used as a simple defrost start, or it may be used as a safeguard if the normal signal fails to appear. Regulator til temperaturstyring — AK-CC manual. Where is the manual http: Example During day operation there is a temperature difference of e.

Author:Akilkree Nashura
Country:Mayotte
Language:English (Spanish)
Genre:Travel
Published (Last):9 June 2012
Pages:343
PDF File Size:9.45 Mb
ePub File Size:3.98 Mb
ISBN:658-9-43812-837-1
Downloads:77265
Price:Free* [*Free Regsitration Required]
Uploader:Yozshuk



Dizuru If data communication is used, it is important that the installation of the data communication cable is performed correctly. Transcritical CO2 system in a small supermaket. Temperaturregler — EKC D1. Danfoss EKC D1 temperature settings The snowflake is blinking, but i have other freezers that d blinking too and no problems. System Management Electronic Controls: Defrost on demand — aggregate refrigeration time Set here is the refrigeration time allowed without defrosts.

Here are the messages that may appear: To avoid a too low setting of the setpoint, the min. S3 is placed in the air flow before the evaporator. A sensor before and after the evaporator: When you have changed the value, eoc the new value by once more pushing the middle button.

Modulo interface EKC Make any necessary changes in the respective parameters. Go to About section Our Engineering. Where is the manual http: Only the function belonging to the selected application is shown. ON-time in minutes Min. Regulator til temperaturstyring — EKC D1. Low temperature alarm Low t. All trademarks in this material are property of the respecitve companies. The possible functions are described in menus o02 and o Door alarm Door Alarm A5: Copying still going on The information 22d1 be found in o65 or o66 a couple of seconds after copying has been started.

Temperature difference for night time cover When the night time cover is placed over the appliance, the difference between the S3 and S4 sensors will fall due to the reduced cooling loss.

The survey can be seen on page Running times To prevent irregular operation, values can be set for the time the compressor is to run once it has been started. EKC EKC controllers can be used for a wide range of different refrigeration applications — from control of air temperatures and defrost to more advanced applications, including control of light and fans. EKC D1 If the emc is built into a network with data communication, it must have an address, and the master gateway of the data communication must then know this address.

If the settings in the controller are to be protected with an access code you can set a numerical value between 0 and Date setting t45 Clock: The interval time is not active when set to 0.

Regulation is carried out when the input is short-circuited, and regulation is stopped when the input is put in pos.

If there is power failure ekv timer value will be saved and continue from here when the power returns. Select your own number. The individual status codes have the following meanings: Results 1 to 9 of 9.

Most 10 Related.

GONOSEN NO KATA PDF

EKC 202D1 PDF

Darn Danfoss EKC D1 temperature settings The snowflake is blinking, but i have other freezers that are blinking too and no problems. This timer function can be used as a simple way of starting defrosts, but it will always act as safety defrost if one of the subsequent defrost starts is not received. Defrosting is only started for the current controller. Results 1 to 9 of 9. Push the middle button again to freeze the value.

BABBIE PRACTICA CERCETARII SOCIALE PDF

084B8522 EKC 202B Контроллер температуры

Daikree Ekcc refrigeration and the fans are stopped. Copying was not correct. Go to media section Danfoss Media Center. Running times To prevent irregular operation, values can be set for the time the compressor is to run once it has been started.

DESCARGAR LIBRO VAMOS A BUSCAR UN TESORO JANOSCH GRATIS PDF

Continue session

The function is furthermore only relevant if you have chosen defrost ekv interval start d A03 With data communication the importance of the individual alarms can be defined. Danfoss EKC D1 temperature settings relay sticking- if cooling led isnt lit- tap it with a screwdriver see if it stops. Fan cut in during defrost Here you can set whether fan is to operate during defrost. The few selected settings will now be transferred to the menu. Low temperature alarm Low t.

Related Articles